How to Cut Retaining Wall Capstones

There are a few tools that you will need in order to cut retaining wall capstones. You will need a masonry saw, chisel, and hammer. First, you will need to mark the stone where you want to make your cuts.

Next, you will need to score the stone along the line that you marked with the masonry saw. Be sure to wear safety goggles when using the masonry saw. Once you have scored the stone, you will then need to use the chisel and hammer to break off the piece of stone that you want to remove.

Again, be sure to wear safety goggles when using the chisel and hammer.

  • Select the desired location for the retaining wall and mark it out with string or spray paint
  • Excavate the area within the marked boundaries to a depth of 8 inches
  • Install a layer of gravel in the bottom of the excavation and compact it with a hand tamper or plate compactor
  • Lay the first course of retaining wall block on top of the gravel base, using a level to ensure each block is level with the others
  • Cut blocks as necessary to fit along the perimeter of the excavation
  • Fill in behind each block with more gravel and compact it again before continuing to lay additional courses of the block until reaching ground level
  • 6 To finish off the top of your wall, cut capstones to fit snugly on top of each row of blocks and secure them in place with construction adhesive or mortar mix

How to Cut Retaining Wall Capstones


How Do You Remove a Capstone from a Retaining Wall?

Assuming you would like tips on how to remove a capstone from a retaining wall: Use a sledgehammer: Place the chisel end of the hammer against the edge of the stone you wish to remove. Strike the chisel with another piece of metal or a second sledgehammer to loosen the stone.

Work your way around the entire circumference of the stone until it is loose enough to be removed by hand. Pry bar: A pry bar can also be used to loosen and remove stones from a retaining wall. First, use the claw end of the bar to get under one side of the stone.

Then, lever up on the pry bar while pushing down on the handle with your other hand. As you do this, the stone should start to loosen and can then be removed by hand.

How Do You Cut a Corner Cap on a Retaining Wall?

If you’re looking to add a little extra flair to your retaining wall, cutting a corner cap can be a great way to do it. But how do you actually go about doing it? Here’s a step-by-step guide:

  • Begin by measuring the length and width of the retaining wall. You’ll need to know these dimensions in order to cut the correct size corner cap.
  • Next, use a pencil or chalk to mark out the desired shape of the corner cap on a piece of paper. Once you have your template, cut it out with scissors.
  • Place the template on top of a piece of stone or concrete that is large enough to accommodate it. Trace around the template with a pencil or marker.

  • Carefully use a chisel and hammer to remove any excess material from around the perimeter of the traced shape. Be sure not to chisel too deeply, as you don’t want to damage the underlying surface. 

How Do You Cut a Retaining Wall?

Building a retaining wall is a great way to add visual interest and functionality to your property. But before you can enjoy the fruits of your labor, you need to know how to cut a retaining wall. Here are some tips to help you get started:

  1. The first step is to mark the area where you will be cutting the retaining wall. Use a string line or tape measure to make sure that the lines are straight.
  2. Next, use a power saw or hand saw to cut through the bricks or blocks that make up the retaining wall. If you’re using a power saw, be sure to wear safety goggles and gloves.
  3. Once the bricks or blocks have been cut, remove any debris from the area so that it’s clean and safe for work.
  4. Finally, use a trowel or chisel to smooth out any rough edges on the bricks or blocks.

What Saw to Cut Retaining Wall Blocks?

There are a few different types of saws that can be used to cut retaining wall blocks. The most common type of saw is a masonry saw, which has a diamond blade that can quickly and easily cut through the concrete. Other types of saws that can be used include an abrasive cutoff saw or a reciprocating saw with a carbide-tipped blade.

How to Cut Retaining Wall Capstones


How to Cut Retaining Wall Caps With a Chisel

If you’re looking to add a little bit of extra flair to your retaining wall, why not try adding some retaining wall caps? They can really dress up the look of your wall and add some extra visual interest. But how do you go about cutting them?

The best way to cut retaining wall caps is with a chisel. First, mark out where you want to make your cuts. Then, using a sharp chisel, score along your lines.

Finally, use a hammer to tap the chisel and break off the pieces. Now that you know how to cut retaining wall caps with a chisel, get out there and give it a try!


If you’re looking to add a little extra flair to your retaining wall, why not try capping it with some beautiful stone? Capping your retaining wall with capstones is a great way to give it a finished look. Not only that, but it can also help protect the wall from weather damage.

Cutting retaining wall capstones can be a bit tricky, but with a little patience and the right tools, you’ll be able to do it like a pro! First, you’ll need to mark out where you want to make your cuts. Then, using a masonry saw or angle grinder, carefully cut along the marked lines.

Once you’ve made your cuts, clean up any rough edges with a hammer and chisel. With just a little bit of effort, you can take your retaining wall from ordinary to extraordinary! Give it a try today!

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *